Flashing

How To Restore/Unbrick Motorola XT907 From A Boot Loop

How To Restore/Unbrick Motorola XT907 Droid Razr M From A Boot Loop

How To Restore/Unbrick Motorola XT907 Droid Razr In Boot Loop

The Motorola Droid Razr M is one of those great smartphones from Motorola[now Lenovo]. The device packs great specs which include a super brilliant AMOLED display[I love it] which pours out saturated colors, currently runs on Android Kitkat 4.4.2, a very fast snapdragon S4 plus processor paired with 1GB of RAM, supports 4G LTE, expandable storage, 2000mAh battery, and a slim design are some of its main specs.

Have you seen this ?
And this as well ?

Like every other Android smartphone, there is always sometimes when you might get a boot loop which means the phone keeps restarting or just hangs on the logo[kind of freeze]. Sometimes trying to play around with the OS can cause a boot loop.

So if your Motorola XT907 also known as Motorola Razr M is soft bricked or in a boot loop, stuck on the red eye, stuck on fastboot, hangs, restarts without measure, virus infected, ultra slow in which factory resetting it couldn’t help or you just want to reload/upgrade the firmware, then you are in the right place for a perfect solution to the issues aforementioned.

You can also use this to fix fastboot error issues whereby the Moto Razr M boots into fastboot mode automatically due to a previous flashing error.

Note..

  • Your device will return to its factory state.
  • You will lose all of your user data.
  • Backup the phone if it’s accessible to prevent loss of data.
  • You don’t need to unlock the bootloader before flashing the firmware because it’s official.
  • You must charge your Razr M battery to its capacity before proceeding.
Also Trending..

If you are ready, all you need to unbrick your xt907 is just below

How To Restore/Unbrick Motorola XT907 Droid Razr M In Boot Loop

Requirements:
 
Instructions:

According to the requirements above, you can either use Snapdragon fastboot or RSDLite 6.2.4[recommended].

If you downloaded the Snapdragon Fastboot drivers, please follow the steps below.

Steps To Reinstall Factory Firmware / Unbrick To Moto XT907

 
METHOD 1
  • Boot your XT907 to AP fastboot mode by pressing Vol +, Vol -, and power key. Then in the window that pops up[with AP Fastboot, Recovery, Bootloader, Factory], scroll down using Volume down and use Volume up to select AP Fastboot.
  • Extract and paste the Snapdragon Fastboot folder to your desktop.
  • Extract the firmware package for the Razr M and paste all the files inside the Snapdragon fastboot folder.
  • Connect your Motorola Droid Razr M to the Pc via a good USB cable.
  • Open the Snapdragon Fastboot folder, hold down the shift key, right-click and select Open Command Window Here.
  • In the command prompt window that will pop up, carefully type the commands below(one at a time) and hit the enter key on your computer after each line.

fastboot -w
fastboot flash partition gpt.bin
fastboot flash sbl1 sbl1.mbn
fastboot flash sbl2 sbl2.mbn
fastboot flash sbl3 sbl3.mbn
fastboot flash rpm rpm.mbn
fastboot flash tz tz.mbn
fastboot flash aboot emmc_appsboot.mbn
fastboot flash modem NON-HLOS.bin
fastboot flash fsg fsg.mbn
fastboot erase modemst1
fastboot erase modemst2
fastboot flash logo logo.bin
fastboot flash boot boot.img
fastboot erase tombstones
fastboot flash recovery recovery.img
fastboot flash system system.img
fastboot continue

  • After typing the last command, your phone will restart and would be back on its feet within minutes. You can now set it up as usual.
Method 2[Faster and easier]
  • The second method is pretty easy. Just download RSDLite v6.2.4 above instead of the Snapdragon Fastboot.
  • Install it and launch it via the shortcut on your windows desktop.
  • Boot your XT907 to fastboot mode by pressing Vol +, Vol -, and power key. Then in the window that pops up[with AP Fastboot, Recovery, Bootloader, Factory], scroll down and use volume up to select AP Fastboot.
  • Connect the Razr M to your windows PC.
How To Restore/Unbrick Motorola XT907 Droid Razr M From A Boot Loop
  • Click on theafter filename.
How To Restore/Unbrick Motorola XT907 Droid Razr M From A Boot Loop
  • and select the firmware file VZW_XT907_4.4.2-KDA20.62-15.1_1FF.xml [not extracted…. ] then click open.
[Image:How To Restore/Unbrick Motorola XT907 Droid Razr In Boot Loop]
  • Now select Decompress and Start Flashing, then wait for it to decompress the files and begin the flashing.
[Image:How To Restore/Unbrick Motorola XT907 Droid Razr In Boot Loop]
  • Flashing will take a while. Just sit back and take a glass of water, the flashing will be done in a short while. When it’s finished, you will see a PASS notification. You can now unplug your phone and set it up as usual.
How To Restore/Unbrick Motorola XT907 Droid Razr M In Boot Loop
  • If you get stocked at the AP Fastboot screen after rebooting, just type this commands on your PC and hit enter after each line of command.
    fastboot oem fb_mode_clear
    fastboot continue


    Your device should now reboot without any more issues.

    Please share and also drop your comments

8 Comments

8 Comments

  1. M Taha

    October 5, 2016 at 1:55 pm

    VZW_XT907_4.4.2-KDA20.62-15.1_1FF.xml file link is adware nothing else.

    View Comment
  2. Mba Christian Ihechi

    October 5, 2016 at 2:05 pm

    @ M Taha, the file "VZW_XT907_4.4.2-KDA20.62-15.1_1FF.xml" or its link is not an adware. It's the stock firmware for Motorola Razr M XT907. Try downloading it again.

    View Comment
  3. Anonymous

    November 29, 2016 at 3:22 pm

    Thanks mate….. You saved my life with it… I don't have any words to say
    Thanks once again and keep it up and coming!!!!

    View Comment
  4. Mba Christian Ihechi

    November 29, 2016 at 3:38 pm

    You are welcome and thanks for dropping such a positive comment.

    View Comment
  5. Mahmud

    December 26, 2016 at 10:23 pm

    Thanks again. Should in case I get stocked at ap fastboot, where should I type the commands as mentioned above. I am a bit confused.

    View Comment
    • Christianihechi

      December 26, 2016 at 10:43 pm

      Just connect the device to your PC while it’s still in the AP Fastboot screen, open a command window inside the Snapdragon Fastboot folder and then type the commands below, one after another.

      First of all, Type
      fastboot oem fb_mode_clear
      and then hit the Enter button on your PC. Next, type
      fastboot continue
      and hit the enter key as well. This will boot up your phone. I hope it’s clear now.

      View Comment
  6. Kehinde

    May 5, 2017 at 8:37 pm

    Brotherly, I must say that i am very impressed. This phone has been bricked since June 2015 and I have tried all means to unlock it, all with no positive result. until I found this your website today. Everything worked perfectly!!!
    Thank you very much and am very grateful. God bless.

    View Comment
    • Christianihechi

      May 5, 2017 at 9:21 pm

      Thanks for taking your time to drop such a positive comment. Please share the post and also like our Facebook page. If you have any other issue, you can always ask for assistance here. Enjoy!

      View Comment

Leave a Reply

Get more stuff

Subscribe to our mailing list and get interesting stuff and updates to your email inbox.

To Top